-
Industrial Pressure Transmitter
-
Low Cost Pressure Transmitter
-
Piezoresistive Differential Pressure Transmitter
-
Piezoresistive Pressure Sensor
-
Liquid Level Transmitter
-
Capacitive Fuel Level Sensor
-
Thin Film Pressure Sensor
-
Infrared Temperature Transmitter
-
Digital Pressure Gauge
-
Digital Flow Switch
-
Magnetostrictive Liquid Level Transmitter
-
Industrial Vibration Sensor
-
Liquid Leakage Sensor
-
Submersible Level Transmitter
-
Magnetostrictive Displacement Sensor
100MΩ Piezoresistive Differential Pressure Transmitter
Housing | Stainless Steel 304 | Diaphragm | Stainless Steel 316L |
---|---|---|---|
O-ring | Viton | Filled Liquid | Silicon Oil |
Pressure Port | G1/4 Female | Storage Temp. | -40~120 |
High Light | 100MΩ Piezoresistive Differential Pressure Transmitter,50VDC flush pressure transmitter,50VDC diaphragm pressure transmitter |
Differential Pressure Transmitter
Features
·Full stainless steel construction, compact size, easy installation;
·Using piezoresistive differential pressure sensor, 316L isolated diaphragm;
·Temperature compensation and aging, stable performance;
·Zero and span adjustable outside;
Introduction
SPT90 uses piezoresistive differential pressure sensor as sensing element. Silicon oil is filled in between die and two diaphragms, when measured differential pressure is added on two diaphragm, the pressure could be transferred onto die through silicon oil. Sensor die connects with amplifier circuit through wires, using semi-conductor’s piezoresistive effect, transforming differential pressure signal into electric signal. The whole product is used for differential pressure measurement of petroleum, chemi-industry, power station and hydrology, etc.
Specification
Min. | Typ. | Max. | Unit | ||
0.5 | 0.5 | %FS | |||
0.5 | 0.5 | ||||
Zero Thermal error | 0~100kPa | 0.75 | 1.25 | ±%FS, @25℃ | |
200~3500kPa | 0.5 | 0.75 | |||
FS Thermal error | 0~100kPa | 0.75 | 1.25 | ||
200~3500kPa | 0.5 | 0.75 | |||
Stability | ≤200kPa | 0.5 | %FS/year | ||
≤3500kPa | 0.2 | ||||
Static pressure effect | 0.05 | ±%FS, each 100kPa | |||
Compensation temp. | 0~50 | ℃ | |||
Operation temp. | -10~80 | ||||
Storage temp. | -40~120 |
Electric Characteristic
Power supply | 2-wire 15~28VDC 3-wire 15~28VDC |
Output signal | 2-wire 4~20mADC 3-wire 0/1~5VDC,0~10/20mADC |
Electric connection | plug connection or Φ7.2mm 7-pin cable |
Response time(10%~90%) | ≤1ms |
Insulation resistor | 100MΩ,50VDC |
Construction Material
Housing | stainless steel 1Cr18Ni9Ti |
Diaphragm | stainless steel 316L |
O-ring | Viton |
Filled liquid | silicon oil |
Pressure port | G1/4 female |
Environment Condition
Shock effect | ≤1% at 3gRMS, 30~2000Hz |
Impact | ≤1% at 100g, 10ms |
Lifetime | 1×108 pressure cycles |
Media | liquid or gas which is compatible with construction material |
Order Guide
Order Note
1. We suggest to install tri-valve between the measured point and transmitter to protect the media adding on transmitter’s positive and negative cavities slowly;
2. We suggest to make two pressure ports horizontally to reduce installation direction effect;
3. Please pay attention that the static pressure should be less than 20Mpa, transmitter positive and negative cavity should be in the rating pressure range;
4. If the user has special requirement, please feel free to contact our company.